We get to check quite a lot of actually cool filaments and check out a bunch of various printers at MatterHackers. Over the previous yr, the variety of out there filaments has skyrocketed as has the variety of out there printers and printer choices. Sadly, the quantity of obtainable details about all of those choices leaves a lot to be desired.

On high of questions on varied filaments, we get quite a lot of questions on twin extrusion.

Do I would like twin extrusion? What sorts of issues can I print with twin extrusion? Is twin extrusion higher than single?

We love sensible purposes of 3D printing, so we thought it could be good to highlight 2 newer filaments in addition to twin extrusion printing by designing and printing upgrades for an older printer.

We now have an previous KitTaz (Taz 3), by Lulzbot, from 2013/2014 that has seen fairly a little bit of use. The plastic linear bearings developed a little bit of play, and it wanted an overhaul.

Supplies

The IGUS tribo-filament was designed to print bearings and different elements that require low friction or low abrasion properties. Should you’ve ever used IGUS parts for different tasks, you already know they make top quality parts, and their filament is not any exception.  It prints simply, cleanly, and has remarkably low friction for a 3D printed half.

Since IGUS focuses on bearings, linear rails, and different associated {hardware}, we figured it made sense to make use of IGUS filament to print replacements.  It’s additionally an ideal solution to highlight their filament to indicate what it could actually do.

We would have liked to switch the next:

• 4 single linear bearings (SLB) for heated mattress (Y axis)
• 1 single linear bearing for X carriage
• 1 double linear bearing (DLB) for X carriage
• 2 double linear bearings for Z axis mounts

I rapidly mocked up a bearing that matched the inventory SLB and printed it out of the Tribo filament to test match and performance.

It got here out fairly effectively for a primary print. The middle gap was a bit of sloppy so there was a little bit of play, nevertheless it confirmed that this materials would work to be used as a bearing. There have been just a few issues we observed whereas wanting on the printed SLB.

The Tribo glides on the sleek rods very easily and quietly, nevertheless it will get soiled rapidly and it doesn’t appear as robust/sturdy because the ABS that the inventory elements had been printed in. The soiled half is solely a beauty situation and never a giant deal, however we needed our Taz to nonetheless look good after the upgrades. The sturdiness is clearly a problem. We don’t need these printed alternative elements to interrupt anytime quickly. Additionally, the Tribo filament is on the costly aspect of filaments. Because the solely half we want the Tribo for is the half contacting the sleek rods, we are able to print the housings out of one other materials.

The inventory Taz items had been printed in ABS. Whereas ABS is a flexible and helpful filament, it tends to warp, and that’s not excellent when printing issues like bearings with tight tolerances. We determined to make use of PETG for the outer housings. PETG is simple to print, has nearly no warp, and is about as robust, if not stronger, than ABS. It additionally has a pleasant shiny floor end. There are just a few totally different PETG filament choices out there – MatterHackers PETG and MadeSolid PET+ are the 2 we print with most frequently for practical elements. Printing temps might very barely, however 240-260C with a heated mattress at 50-60C is suitable the vary. For this venture, we used the MadeSolid PET+ in opaque black to be able to match the unique printed elements.

Twin Extrusion

The inventory SLB has a printed housing, after which a bearing is slid in or pressed into the housing. With twin extrusion we are able to simply mannequin the outer housing and internal bearing and print it out at one time with two totally different supplies.

There are alternative ways to mannequin elements for twin extrusion, however 2 separate STLs are required. I exploit Solidworks for many of my modeling. The best means I’ve discovered for elements like that is to mannequin the half in a single half file, however to not merge all the stable our bodies in order that I can save them as particular person STL recordsdata. By modeling the elements in a single file as separate stable our bodies, each elements are aligned in the identical Cartesian house which permits for straightforward alignment of the STLs in MatterControl.

The gray portion might be printed in PETG. The purple sleeve might be printed within the IGUS tribo-filament.

As a result of the our bodies weren’t merged I can disguise one or the opposite and export the seen half as an STL.

Subsequent, I carry the STLs into MatterControl. I like to simply drag one of many elements into the queue, after which drag the opposite half instantly into the 3D View window. 

When utilizing twin extrusion, the colour of the elements within the 3D View panel signifies the extruder that might be used to print every half. As proven, each of those elements could be printed in the identical materials by Extruder 1.

For this setup, PETG is Extruder 1 and the IGUS filament is Extruder 2. We would like the sleeve printed in IGUS, so we choose the bearing sleeve, then choose the Materials drop down bar on the proper aspect of MatterControl.

We then choose the suitable extruder. 

The colour of the half within the 3D View will change to point that the elements are printed with totally different extruders.

Now, we have to align the elements. Since we modeled them collectively, all we have to do is choose “Align” 

Now the sleeve is correctly aligned contained in the housing.  Save our modifications and we’re nearly able to print.

From our check printing with the IGUS filament, we found that it has pretty low viscosity when at printing temp, so it’s liable to a good bit of oozing. When twin extruding, oozing is commonly a problem with the extruder not at the moment in use. There are just a few methods to fight this. For the bearing print, we’re going to make use of a Wipe Tower.

Wipe Tower is just seen within the Superior view mode. It’s below Settings > Basic > A number of Extruders.

The wipe tower is a stable block of filament printed off to the aspect of the printed half that enables every extruder to prime and wipe earlier than starting the following layer. We simply must specify the dimensions of the tower. Getting into 10mm within the setting will make the wipe tower 10mm x 10mm and it’ll print as tall because the printed half. The wipe tower doesn’t present up within the 3D view, however we are able to have a look at it within the Layer View window.

The wipe tower will alternate between extruder 1 & 2 which helps each prime the nozzles in addition to get rid of some stringing/oozing from the precise printed half. On this picture, the black traces are extruder 1 and the teal traces are extruder 2.

The MakeIt Professional was used to print. We used coarse high quality settings – .3mm layer peak – primarily to get the half printed rapidly to check – and so they nonetheless got here out effectively on the primary attempt. 

There are just a few areas the place the Tribo filament bled into the PETG and vice versa. However this was fairly minimal and shouldn’t have any impact on the perform of the half. The printed model is sort of a bit smaller in measurement and weight than the inventory model with the pressed-in bearing. Whereas this doesn’t actually have an effect on the efficiency in any important means, we’re at all times a fan of constructing issues extra compact and environment friendly.

As you may see within the video beneath, the bearing works nice. The printed bearing can be fairly a bit quieter than the inventory bearing.

We’d name {that a} success! We needed to alter the scale a bit to get the precise match we had been on the lookout for – as little play as doable whereas permitting free motion alongside the sleek rod – however the finish outcomes had been glorious.

We’re not accomplished, although. Whereas we’re very pleased with the twin extrusion outcomes, we additionally needed to indicate how you should use 2 supplies on a component with out utilizing a twin extrusion 3D printer.

We modified the mannequin a bit in order that we are able to print the outer housing and the internal sleeve individually, and press them collectively.

Whereas it requires 2 separate print jobs, it has just a few advantages over printing in a single piece.

First, the prints are a lot cleaner. As a result of we’re simply utilizing 1 nozzle, oozing/stringing isn’t a problem. Second, it took us just a few iterations with the twin extrusion to get the internal diameter of the bearing to suit completely. The primary ones had a little bit of play and the two^nd model was a bit of tight. It’s a lot faster and simpler to print the internal sleeve, check the match, after which alter accordingly than it’s to must print the entire bearing meeting.

Lastly, and most vital to us for this venture, printing them individually makes the elements modular and extra simply replaceable. If the internal sleeve begins to develop some play, we are able to simply print a brand new sleeve and change it reasonably than having to print an entire new bearing meeting.

We printed out all of the bearings and put in them on the machine.

X carriage – double linear bearing on high rail, single on backside rail

Y-axis single bearings mounted to the mattress plate

Z-axis double bearing

We’re very pleased with the outcomes. The printer strikes smoother, has much less play, and is noticeably quieter with the brand new bearings put in. The IGUS filament works superbly as linear bearing materials, and the PETG is robust, sturdy, and has a clear, shiny floor end. It’s an important mixture.

We’ve made our designs – each the twin and single extrusion variations – out there for obtain. They’ll work on any Taz 3/KitTaz, Taz 4, or Taz 5. The Taz 5 doesn’t use the identical Z-axis bearings, however the X and Y axis bearings are the identical. Print ‘em out, improve your machine, and ship us photos!

Together with the bearing upgrades, we additionally upgraded the electronics to an Azteeg X3 Professional with a Viki2 LCD show, and added the Kraken quad scorching finish, by E3D. Search for all these particulars and a few quad extrusion craziness within the subsequent function article.

Thanks for studying. Questions and feedback are at all times welcome and, as at all times,

Glad Printing!